# generated by PrusaSlicer 2.9.6 on 2026-07-09 at 17:47:44 UTC [print:0.20mm STRUCTURAL @COREONE 0.4 Bambu PA6-CF] arc_fitting = emit_center automatic_extrusion_widths = 0 automatic_infill_combination = 0 automatic_infill_combination_max_layer_height = 100% avoid_crossing_curled_overhangs = 0 avoid_crossing_perimeters = 1 avoid_crossing_perimeters_max_detour = 0 bed_temperature_extruder = 0 bottom_fill_pattern = monotoniclines bottom_solid_layers = 3 bottom_solid_min_thickness = 0.5 bridge_acceleration = 1500 bridge_angle = 0 bridge_flow_ratio = 1 bridge_speed = 50 brim_separation = 0.15 brim_type = outer_only brim_width = 5 compatible_printers = compatible_printers_condition = printer_model=~/(COREONE|COREONEOAK|COREONEMMU3)/ and nozzle_diameter[0]==0.4 and printer_notes!~/.*HT400.*/ complete_objects = 0 custom_parameters_print = default_acceleration = 3000 dont_support_bridges = 0 draft_shield = disabled elefant_foot_compensation = 0.2 enable_dynamic_overhang_speeds = 1 ensure_vertical_shell_thickness = enabled external_perimeter_acceleration = 1500 external_perimeter_extrusion_width = 0.45 external_perimeter_speed = 50 external_perimeters_first = 1 extra_perimeters = 0 extra_perimeters_on_overhangs = 0 extrusion_width = 0.45 fill_angle = 45 fill_density = 100% fill_pattern = rectilinear first_layer_acceleration = 500 first_layer_acceleration_over_raft = 0 first_layer_extrusion_width = 0.5 first_layer_height = 0.2 first_layer_infill_speed = 100 first_layer_speed = 45 first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 0.8 fuzzy_skin_thickness = 0.3 gap_fill_enabled = 1 gap_fill_speed = 60 gcode_comments = 0 gcode_label_objects = firmware gcode_resolution = 0.008 gcode_substitutions = infill_acceleration = 6000 infill_anchor = 2 infill_anchor_max = 12 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.45 infill_first = 0 infill_overlap = 15% infill_speed = 120 inherits = 0.20mm STRUCTURAL @COREONE 0.4 interface_shells = 0 interlocking_beam = 0 interlocking_beam_layer_count = 2 interlocking_beam_width = 0.8 interlocking_boundary_avoidance = 2 interlocking_depth = 2 interlocking_orientation = 22.5 ironing = 0 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_bead_width = 85% min_feature_size = 25% min_skirt_length = 4 mmu_segmented_region_interlocking_depth = 0 mmu_segmented_region_max_width = 5 notes = only_one_perimeter_first_layer = 0 only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = {input_filename_base}_0.4n_{layer_height}mm_{printing_filament_types}_{printer_model}_{print_time}.gcode over_bridge_speed = 50% overhang_speed_0 = 15 overhang_speed_1 = 25 overhang_speed_2 = 45 overhang_speed_3 = 90% overhangs = 1 perimeter_acceleration = 2500 perimeter_extruder = 1 perimeter_extrusion_width = 0.45 perimeter_generator = arachne perimeter_speed = 70 perimeters = 2 post_process = print_settings_id = raft_contact_distance = 0.15 raft_expansion = 1.5 raft_first_layer_density = 90% raft_first_layer_expansion = 3 raft_layers = 0 resolution = 0 scarf_seam_entire_loop = 0 scarf_seam_length = 20 scarf_seam_max_segment_length = 1 scarf_seam_on_inner_perimeters = 0 scarf_seam_only_on_smooth = 0 scarf_seam_placement = everywhere scarf_seam_start_height = 0% seam_gap_distance = 15% seam_position = random single_extruder_multi_material_priming = 0 skirt_distance = 6 skirt_height = 1 skirts = 0 slice_closing_radius = 0.049 slicing_mode = regular small_perimeter_speed = 50 solid_infill_acceleration = 4000 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.45 solid_infill_speed = 140 spiral_vase = 0 staggered_inner_seams = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_auto = 0 support_material_bottom_contact_distance = 0 support_material_bottom_interface_layers = 0 support_material_buildplate_only = 0 support_material_closing_radius = 2 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 0 support_material_extrusion_width = 0.4 support_material_interface_contact_loops = 0 support_material_interface_extruder = 0 support_material_interface_layers = 3 support_material_interface_pattern = auto support_material_interface_spacing = 0.2 support_material_interface_speed = 50 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 120 support_material_style = snug support_material_synchronize_layers = 0 support_material_threshold = 40 support_material_with_sheath = 0 support_material_xy_spacing = 80% support_tree_angle = 40 support_tree_angle_slow = 25 support_tree_branch_diameter = 2 support_tree_branch_diameter_angle = 5 support_tree_branch_diameter_double_wall = 8 support_tree_branch_distance = 1 support_tree_tip_diameter = 0.8 support_tree_top_rate = 30% thick_bridges = 0 thin_walls = 0 toolchange_ordering = optimized top_fill_pattern = monotoniclines top_infill_extrusion_width = 0.42 top_one_perimeter_type = none top_solid_infill_acceleration = 2000 top_solid_infill_speed = 80 top_solid_layers = 3 top_solid_min_thickness = 0.5 travel_acceleration = 7000 travel_short_distance_acceleration = 250 travel_speed = 350 travel_speed_z = 12 wall_distribution_count = 1 wall_transition_angle = 10 wall_transition_filter_deviation = 25% wall_transition_length = 100% wipe_tower = 0 wipe_tower_acceleration = 0 wipe_tower_bridging = 10 wipe_tower_brim_width = 2 wipe_tower_cone_angle = 25 wipe_tower_extra_flow = 250% wipe_tower_extra_spacing = 110% wipe_tower_extruder = 0 wipe_tower_no_sparse_layers = 0 wipe_tower_width = 60 xy_size_compensation = 0 [filament:Bambu PA6-CF] bed_temperature = 100 bridge_fan_speed = 20 chamber_minimal_temperature = 40 chamber_temperature = 50 compatible_printers = compatible_printers_condition = nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_model=~/(COREONE|COREONEOAK|COREONEL)/ and ! single_extruder_multi_material compatible_prints = compatible_prints_condition = cooling = 1 cooling_perimeter_transition_distance = 10 cooling_slowdown_logic = consistent_surface custom_parameters_filament = "" disable_fan_first_layers = 4 enable_dynamic_fan_speeds = 0 end_filament_gcode = "; Filament-specific end gcode" extrusion_multiplier = 0.96 fan_always_on = 0 fan_below_layer_time = 15 filament_abrasive = 1 filament_colour = #BBBBBB filament_cooling_final_speed = 2.5 filament_cooling_initial_speed = 5 filament_cooling_moves = 3 filament_cost = 80 filament_density = 1.1 filament_deretract_speed = nil filament_diameter = 1.75 filament_flush_speed = 0 filament_flush_volume = 0 filament_infill_max_crossing_speed = 140 filament_infill_max_speed = 0 filament_load_time = 10.9 filament_loading_speed = 10 filament_loading_speed_start = 50 filament_max_volumetric_speed = 8 filament_minimal_purge_on_wipe_tower = 35 filament_multitool_ramming = 0 filament_multitool_ramming_flow = 10 filament_multitool_ramming_volume = 10 filament_notes = "" filament_purge_multiplier = 100% filament_ramming_parameters = "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387" filament_retract_before_travel = nil filament_retract_before_wipe = nil filament_retract_layer_change = nil filament_retract_length = nil filament_retract_length_toolchange = nil filament_retract_lift = nil filament_retract_lift_above = nil filament_retract_lift_below = nil filament_retract_restart_extra = nil filament_retract_restart_extra_toolchange = nil filament_retract_speed = nil filament_seam_gap_distance = nil filament_settings_id = "" filament_shrinkage_compensation_xy = 0% filament_shrinkage_compensation_z = 0.28% filament_soluble = 0 filament_spool_weight = 197 filament_stamping_distance = 45 filament_stamping_loading_speed = 26.5 filament_toolchange_delay = 0 filament_travel_lift_before_obstacle = nil filament_travel_max_lift = nil filament_travel_ramping_lift = nil filament_travel_slope = nil filament_type = PA filament_unload_time = 8.9 filament_unloading_speed = 60 filament_unloading_speed_start = 60 filament_vendor = Prusa Polymers filament_wipe = nil first_layer_bed_temperature = 100 first_layer_temperature = 275 full_fan_speed_layer = 0 idle_temperature = 130 inherits = Prusament PA11 Carbon Fiber @COREONE max_fan_speed = 40 min_fan_speed = 0 min_print_speed = 20 overhang_fan_speed_0 = 0 overhang_fan_speed_1 = 0 overhang_fan_speed_2 = 0 overhang_fan_speed_3 = 0 slowdown_below_layer_time = 20 start_filament_gcode = "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S45 ; set heatbreak target temp" temperature = 275 [printer:Prusa CORE One 0.4 nozzle jcs Bambu PA6-CF] autoemit_temperature_commands = 1 bed_custom_model = bed_custom_texture = bed_shape = 0x0,250x0,250x220,0x220 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n{if layer_z > 150}\nM201 X{interpolate_table(layer_z, (0,7000), (150,7000), (200,4000), (270,2000))} Y{interpolate_table(layer_z, (0,7000), (150,7000), (200,4000), (270,2000))}\n{endif}\n between_objects_gcode = binary_gcode = 1 color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change cooling_tube_length = 20 cooling_tube_retraction = 45 custom_parameters_printer = default_filament_profile = "Prusament PLA @COREONE" default_print_profile = 0.20mm STRUCTURAL @COREONE 0.4 deretract_speed = 10 end_gcode = {if layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM141 S0 ; disable chamber control\nM107 ; turn off fan\nG1 X242 Y211 F10200 ; park\nG4 ; wait\nM572 S0 ; reset PA\nM84 X Y E ; disable motors\n; max_layer_z = [max_layer_z] extra_loading_move = -52 extruder_clearance_height = 33 extruder_clearance_radius = 75 extruder_colour = "" extruder_offset = 0x0 gcode_flavor = marlin2 high_current_on_filament_swap = 0 host_type = prusalink inherits = Prusa CORE One 0.4 nozzle layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z] machine_limits_usage = emit_to_gcode machine_max_acceleration_e = 5000,2500 machine_max_acceleration_extruding = 7000,2500 machine_max_acceleration_retracting = 2500,2500 machine_max_acceleration_travel = 7000,2500 machine_max_acceleration_x = 10000,2500 machine_max_acceleration_y = 10000,2500 machine_max_acceleration_z = 400,200 machine_max_feedrate_e = 100,100 machine_max_feedrate_x = 350,160 machine_max_feedrate_y = 350,160 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 10,10 machine_max_jerk_x = 10,8 machine_max_jerk_y = 10,8 machine_max_jerk_z = 2,2 machine_max_junction_deviation = 0.01,0.01 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 270 min_layer_height = 0.07 multimaterial_purging = 140 nozzle_diameter = 0.4 nozzle_high_flow = 0 parking_pos_retraction = 84 pause_print_gcode = M601 prefer_clockwise_movements = 0 print_host = printer_model = COREONE printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_MODEL_COREONE\nPG\nNO_TEMPLATES printer_settings_id = printer_technology = FFF printer_variant = 0.4 printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 1 retract_before_travel = 2 retract_before_wipe = 80% retract_layer_change = 1 retract_length = 0.3 retract_length_toolchange = 0 retract_lift = 0.2 retract_lift_above = 0 retract_lift_below = 269 retract_restart_extra = -0.25 retract_restart_extra_toolchange = 0 retract_speed = 30 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = M17 ; enable steppers\nM862.1 P[nozzle_diameter] A{(filament_abrasive[0] ? 1 : 0)} F{(nozzle_high_flow[0] ? 1 : 0)} ; nozzle check\nM862.3 P "COREONE" ; printer model check\nM862.5 P2 ; g-code level check\nM862.6 P"Input shaper" ; FW feature check\nM115 U6.5.7+12836\n\nM555 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{((min(print_bed_max[0], max(first_layer_print_min[0] + 32, first_layer_print_max[0])))) - ((min(print_bed_max[0], first_layer_print_min[0] + 32) - 32))} H{((first_layer_print_max[1])) - ((max(0, first_layer_print_min[1]) - 4))}\n\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\n\n{if chamber_minimal_temperature[initial_tool]!=0}\nM140 S115 ; set bed temp for chamber heating\n{else}\nM140 S[first_layer_bed_temperature] ; set bed temp\n{endif}\n\nM109 R{((filament_notes[0]=~/.*MBL160.*/) ? 160 : (filament_notes[0]=~/.*HT_MBL10.*/) ? (first_layer_temperature[0] - 10) : (filament_type[0] == "PC" or filament_type[0] == "PA") ? (first_layer_temperature[0] - 25) : (filament_type[0] == "FLEX") ? 210 : 170)} ; wait for temp\n\nM84 E ; turn off E motor\n\nG28 ; home all without mesh bed level\n\n{if chamber_minimal_temperature[initial_tool]!=0}\n; Min chamber temp section\nM104 S{idle_temperature[initial_tool]} ; set idle temp\nG1 Z10 F720 ; set bed position\nG1 X242 Y-9 F4800 ; set print head position\nM191 S{chamber_minimal_temperature[initial_tool]} ; wait for minimal chamber temp\nM141 S{chamber_temperature[initial_tool]} ; set nominal chamber temp\nM107\nM140 S[first_layer_bed_temperature] ; set bed temp\n{else}\nM141 S{chamber_temperature[initial_tool]} ; set nominal chamber temp\n{endif}\n\n{if first_layer_bed_temperature[initial_tool]<=60}M106 S70{endif}\nG0 Z40 F10000\nM104 T{initial_tool} S{if is_nil(idle_temperature[initial_tool])}100{else}{idle_temperature[initial_tool]}{endif}\nM190 R[first_layer_bed_temperature] ; wait for bed temp\nM107\n\nG29 G ; absorb heat\n\nM109 R{((filament_notes[0]=~/.*MBL160.*/) ? 160 : (filament_notes[0]=~/.*HT_MBL10.*/) ? (first_layer_temperature[0] - 10) : (filament_type[0] == "PC" or filament_type[0] == "PA") ? (first_layer_temperature[0] - 25) : (filament_type[0] == "FLEX") ? 210 : 170)} ; wait for MBL temp\n\nM302 S155 ; lower cold extrusion limit to 155C\n\n{if filament_type[initial_tool]=="FLEX"}\nG1 E-4 F2400 ; retraction\n{else}\nG1 E-2 F2400 ; retraction\n{endif}\n\nM84 E ; turn off E motor\n\nG29 P9 X208 Y-2.5 W32 H4\n\n;\n; MBL\n;\nM84 E ; turn off E motor\nG29 P1 ; invalidate mbl & probe print area\nG29 P1 X150 Y0 W100 H20 C ; probe near purge place\nG29 P3.2 ; interpolate mbl probes\nG29 P3.13 ; extrapolate mbl outside probe area\nG29 A ; activate mbl\n\n; prepare for purge\nM104 S{first_layer_temperature[0]}\nG0 X249 Y-2.5 Z15 F4800 ; move away and ready for the purge\nM109 S{first_layer_temperature[0]}\n\nG92 E0\nM569 S0 E ; set spreadcycle mode for extruder\n\nM591 S0 ; disable stuck detection\n\n;\n; Extrude purge line\n;\nG92 E0 ; reset extruder position\nG1 E{(filament_type[0] == "FLEX" ? 4 : 2)} F2400 ; deretraction after the initial one\nG0 E5 X235 Z0.2 F500 ; purge\nG0 X225 E4 F500 ; purge\nG0 X215 E4 F650 ; purge\nG0 X205 E4 F800 ; purge\nG0 X202 Z0.05 F8000 ; wipe, move close to the bed\nG0 X199 Z0.2 F8000 ; wipe, move quickly away from the bed\n\nM591 R ; restore stuck detection\n\nG92 E0\nM221 S100 ; set flow to 100% template_custom_gcode = thumbnails = 16x16/QOI, 313x173/QOI, 480x240/QOI, 380x285/PNG thumbnails_format = PNG toolchange_gcode = travel_lift_before_obstacle = 0 travel_max_lift = 1.5 travel_ramping_lift = 1 travel_slope = 1 use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [presets] print = 0.20mm STRUCTURAL @COREONE 0.4 Bambu PA6-CF sla_print = - default - sla_material = - default - printer = Prusa CORE One 0.4 nozzle jcs Bambu PA6-CF filament = Bambu PA6-CF